SUN Hydraulics RDDA-LCN Direct-Acting Relief Valve Screw Adjustment 70-420 Bar Adjustment Range

SUN Hydraulics RDDA-LCN Direct-Acting Relief Valve Screw Adjustment 70-420 Bar Adjustment Range

Regular price
£88.00
Sale price
£88.00
Regular price
Sold out
Unit price
per 
Shipping calculated at checkout.

SUN Hydraulics RDDA-LCN
 Direct-Acting Relief Valve

 


Sun Hydraulics has established a strong foundation for consistently delivering exceptional performance in all aspects of their business. From product design and service delivery, Sun Hydraulics stands out in the industry.

Since the beginning, Sun products have been setting the standard for the screw-in hydraulic cartridge valve industry. Sun's floating cartridge construction and cavity design approach allows products to operate precisely and reliably at higher pressures and flow rates in the most demanding applications. The generous porting area, coupled with our manifold design and construction techniques, result in integrated packages that can be up to 50% smaller than competitive offerings.

Sun cartridge valves are offered in five primary sizes, with flow capacity and controlled horsepower doubling with each successive size. Within each broad functional area (pressure, flow, load control, etc.), multiple variations are available to help you optimize your control circuit, from individual valves to complete integrated packages. Their expansive product line allows you to develop the best control solution for your hydraulic application.


Direct-acting relief cartridges are normally closed, pressure-limiting valves used to protect hydraulic components from pressure transients. When the pressure at the inlet (port 1) reaches the valve setting, the valve starts to open to tank (port 2), throttling flow to limit the pressure rise. These valves are smooth and quiet, essentially zero leak, dirt tolerant, immune to silting and are very fast.

  • Will accept maximum pressure at port 2; suitable for use in cross port relief circuits.
  • The seals on the adjust screw are exposed to system pressure which means this valve can only be adjusted when the pressure is removed. The setting procedure is; check the setting, remove the pressure, adjust the valve, check the new setting.
  • Valve is relatively insensitive to varying oil temperatures and oil borne contamination.
  • Select a spring range where the desired relief setting is approximately mid-range to high between the minimum and maximum pressure to ensure maximum valve repeatability.
  • Suitable for use in load holding applications.
  • Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.
  • Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.
  • Test pressure for each range is as follows: A range - 2000 psi (138 bar), B range - 1000 psi (69 bar), C range - 4000 psi (276 bar), D range - 800 psi (55 bar), E range - 400 psi (28 bar), S range - 150 psi (10 bar), W range - 3000 psi (207 bar).
  • Reseat meets or exceeds 90% of crack pressure at test setting. Settings lower than the test pressure may result in lower reseat percentages.
  • All 2-port relief cartridges (except pilot reliefs) are physically and functionally interchangeable (same flow path, same cavity for a given frame size).
  • Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

 

Technical Specification

Control - Standard Screw Adjustment
Adjustment Range - 70 - 420 Bar / 1000 - 6000 PSI 70 Bar / 1000 PSI Standard Setting
Seal Material - Buna-N

Cavity T-10A
Series 1
Capacity 95 L/min.
Maximum Operating Pressure 350 bar
Factory Pressure Settings Established at 15 L/min.
Maximum Valve Leakage at Reseat 0,7 cc/min.
Response Time - Typical 2 ms
Reseat >90% of setting
Adjustment - No. of CW Turns from Min. to Max. setting 6
Valve Hex Size 22,2 mm
Valve Installation Torque 41 - 47 Nm
Adjustment Screw Internal Hex Size 4 mm
Locknut Hex Size 15 mm
Locknut Torque 9 - 10 Nm
Model Weight 0.17 kg.
Seal kit - Cartridge Buna: 990310007
Seal kit - Cartridge EPDM: 990310014
Seal kit - Cartridge Viton: 990310006

*Note: Data may vary by configuration.






 Can't Find A Part? Ask us!
We specialise in sourcing hard to find specials, oddballs & obsolete parts, get in touch if you can't see what you are looking for.
01555 772474
sales@uscltd.co.uk



The purchaser of these items must ensure that they are satisfactory for use in the application for which they are intended.
No responsibility can be accepted if any products are incorrectly or inadequately fitted.
Goods may not be exact to image shown.